Natural Hair Technique : Hair Infusion (Www.Embraceyourroots.Net)

I'M going to demonstrate the air infusion technique. The necessary tools are the hair that you're going to add in it needs to be bulk hair of the tracks. You need some scissors, a small comb with a rat tail and some hair clips, a glue gun, which already has your keratin glue, sticks and some extra glue sticks, which we may need one or two more. I'M going to begin by making sure there are no tangles in my clients, hair, it's been shampooed and conditioned, and it is ready for the hair infusion. I like to begin from the back section. I usually start by leaving some of the models hair out all the way around the perimeter. I leave approximately an inch of her hair around each side. The back you can see she has some breakage underneath this, the her hairline underneath her name area. So this style is going to be a good stuff for her, because we're going to use it to add length a little more volume in the back and throughout as we go along and she's going to have the versatility of being able to pull it up. With the exception of the back, because her hair is short back here, she will not be able to pull it up as well or she would have to smooth this out with gel, but otherwise she will be able to wear this now full ponytail, because I'm starting In the back, I'm just going to use the clips to hold down the sections that I'm not working with each other sections, I'm leaving out and it's approximately an inch lift out all the way around her head after sectioning off what I will not be working with. I'M going to put the rest of the front in a ponytail to keep this length out of my way, and this is the first row that the infusion will be applied to next thing. I'M going to do is get my hair, I'm going to be blending a couple of different textures, a couple of different colors into our hair. We have one that is the exact shade over here, which is a number two. We have a number for brown and then we have a number 30 which I'm going to use, as my highlight throughout from the middle section on I like to begin by blending the two colors in for the back area, section of the hair off. I have both colors in hand, I'm going to mix the two so that, as I pick up each section of hair that is going to be put in, I have a little bit of both colors using my comb. I'M going to separate a very small section and move it off to the side, using a clip to hold it in place, wait to take just a small section of hair to make sure the two colors, the brown and the black. The section of hair needs to be proportionate to the amount of hair you're, adding that you're adding in to or maybe just a little bit thicker, not a whole lot. Thicker, I'm going to snip off their own even ends positioning it where it's about a quarter of an inch above my fingertips, I'm going to use the glue gun to apply a little bit of the glue. This is a protein-based glue. It'S the same kind of material as the here keratin, which is a protein apply. Just a few drops just enough to get the tip covered completely with glue. Now, I'm going to use that glue tip to apply it underneath the loose hair for that section blending it in with my fingers using the glue gun once again to blend the tip of it is hot. So when you hold the area with the glue directly to the hair, it's going to melt the glue, helping it blend directly into the hair and I'm going to roll it with my fingers to form a loose part. That'S about the size of a grain of rice! Remember that the glue does not need to be attached on the scalp about a quarter of an inch from the scalp is good enough, so the hair is movable. Move on to our next piece use a clip to vault the hair out of the way, wait to take another section of hair blending, the two colors making sure to cut off any excess hair. So we have a blunt tip using the glue gun, we're going to squeeze off the glue to the tip of the hair, where it's been cut. Blunt applied the glue tip a quarter of an inch from the scalp on the loose hair. Once you put it in use the glue gun tip, which is hot to melt the rest of the glue and spread it evenly across the here and roll it with your fingertips, make sure there is no oil on your hands as any oil would prevent proper adhesion Between the glue and the extensions and your models here, you