How To Blowdry Your Hair With Micro Ring Hair Extensions!

Everyone thought I've been getting a lot of questions asked about my head extensions, so I have got little major links, tensions which were tiny little beads, like paws all attached to my hair. I'Ve got a bit 100 strands N and today, I'm just going to show you how I blow-dry my hair extensions and straighten your extensions and stay all them. So I just wanted to do some videos to give you a guide on what I do myself today is just going to be a short video, and it's just going to be showing how I personally will dry it. I find it the easiest way to do it. It doesn't take long at all of it 20 minutes and it gives a nice sleek and smooth blow-dry any more requests or videos that you would like to see. Then please just leave them in the comments below ok, so I'm just going to start off by putting a little pea-sized amount of argan oil on my hand, and then you can't really see it very well, but I'm just going to rub it through the ends on The hair focus in on the mid length to the ends and then just separate it into two sections at each side and then I'm going to use the Wella sugar left spray, which just adds a little bit volume to the root of your hair. You don't need to add this if you don't like volume, but I just think it works really well to get left at the root and at the back of your hair as well. So I'm just rubbing that all in and just giving it a lot of scrunch up at the top and you're just going to part your hair, whatever part, and that you have so I'm just going to go for the side today. I sometimes change it to the middle, but today I'm just going to do the side parting make sure you give your hair a good brush through. You want to make sure all the knots are out, but not pulling too hard or the extensions at the root, because you don't any of the microbeads out. So if you hold it at the top, then it's just going to secure that area so that you're not doing any of the extensions out. So just take a small section. It doesn't have to be too straight because with extensions they're all and at different parts of your hair anyway, so just clip up and then you're going to dry. That section, so I just take a Denman brush because I think that's quite an easy brush to use. That'S quite white, and it just gives a nice sleek and straight finish, so I'm always bored Ryan's downwards. I saw the way that you're here it's fallen down the way and just give it a little extra will dry at the top just to get some of the wetness away. So I'm always using the splash just to go downwards and hold the brush behind me and just pull it down with the hairdryer. At the same time, the hairdryer I have is the ght ear hair dryer, which I find quite good forgiving a smooth full dry finish. This is on the highest temperature at the moment, so you just carry on repeating those steps over the no bar using the brush and then using hair dryer at the same time, Justin, who are all downward from the loop to the bottom and then you're just going To continue that, with all the other sections, I usually do three sections for each side, but it depends on how thick your hair is. I'M just gon na fast forward this all for you just to see exactly how I do it and then I will move on to the next side. You, okay, so now that side is almost finished. I'M just going to finish off by smoothing over the top section and then I'm going to do exactly the same on the other side. So, as you can see, it has a nice smooth straight finish that you get with the hairdryer and, as you can tell, my hair is naturally curly. So I'm just going to wave my magic wand and finish the other side. So, as you can see, that's my board right at full stage left and it's quite straight and sleek and I'm just want to know, get a hair dryer and put it on a cooler safely and just go over the roots of my hair at the top. Just in case there's any dampness still left up there. You don't want to have a hot temperature when you're doing it right at the root, just because the beads at the top and the bones at the top can melt onto your hair if it's too hot and then I'm just going back with the hot temperature and Just smooth it over the top shaped section making sure that there's no fizzy bit or any bits there are legs away at the front. So that is my board ride and I hope you all enjoyed the video today. That is just the back section for you. You might need to go over it with straighteners, but usually I just kinda laughter, so I don't need to go over that again with the straightness. I hope you all enjoyed this video today and, if there's any requests for any other videos, please just write in the comments below you.