*Detailed* Easy Beginner Friendly 5X5 Hd Closure Wig Install & Baby Hair Tutorial | Unice Hair

Hey pretties, welcome or welcome back to a new video or welcome to my channel where we get pretty stay pretty and act pretty okay period. I am johnny monet and we are back with a new video today before we do get started. Make sure you hit that subscribe button turn on the bell and follow me on my social medias at jonice monae, so the hair i'm using is from united's hair, it's their 5x5 hd lace closure and i got it in 26 inches also in their body wave texture. I'M going to walk y'all through exactly how i get my closures to look like a flawless install so starting off. I already bleached the knots on the closure and plucked it, and i'm going to just go in with my makeup and put it all over my cap. I'M not doing the ball cap just for the simple fact that this is a closure, so it's really not needed, but i'm using a foundation or you can use a concealer whatever works as long as it's as close as to your skin tone as possible, and i Also brushed some of that makeup on the inside of the closure. So now i'm going in with my got to be glued instahoe spray. This spray lasted me about three days with proper care with my installs, but in between each layer of glue, i make sure to blow dry until it's completely dry and sticky, and usually i do about three layers of glue. If that's the only product i'm using in this case, it is, but i just make sure it's super dry and make sure to use cold and hot heat. So since i did the no ball cap method, i have to pull my wig in front of that cap. Just so, we can conceal it a little bit better, and so it's not detected okay. We want this to be a flawless install, so once i have that placed i'm just going to take a little bit more of that got to be spray and spray that, at the front of the hairline, now we're getting into cutting the lace. I always split my lace up into sections just to have better control, so i cut this lace into two sections with scissors and i'm using my razor to cut the lace of the hairline, so it can have a rigid look on this. You really want to take your time with cutting your lace just to make sure you don't have any excess lace or make sure you don't cut off too much lace um. So now for baby hairs. I wanted to keep it very minimal for baby hairs because sometimes it just looks better clean with no baby hairs, but you know i like mines a little dramatic, so i just parted those baby hairs out in the front of my unit and i'm gon na use. My hot comb to get them as flat as possible. Next i go in with my razor and i'm going to go in a downward motion just to make sure that they have some type of black layering to them, and then i'm going to go in with my small flat iron, this flat iron, as well as other Tools are linked to my bio to help you with your installs as a beginner, because i know when i started off. I struggled a little bit, but i just curled those baby hairs outward that way. When we go to lay them, they are already curled and ready to go. I'M using my got to be glued spray again and i'm only spraying the top of the baby hairs, not the whole baby hair and i'm going to use the comb side on my edge brush and just lay them in the direction. I want them to go using my finger in the comb. I hope that makes sense so once i comb them, i follow it up with my finger and just lay them down flat. It definitely takes some practice in getting used to, but once you have it, it's really that easy and simple. I definitely feel like the curling iron definitely helps this step because otherwise um my baby hairs would just lay kind of you know just kind of limp and flat, but i like them better curls, also to have that swap baby hair. Look you don't want to use too much product on them, anyways, i'm adding some hair sheen to the front of the closure, because i really want to focus in on this step, because it's so important, the hot comb and wax stick do well really just makes your Hair look snatched and it really takes it from looking good to great and well put together. So that's what i do. I make sure to focus on the very front of my hair, where the hairline is because it creates that scalp. Look and really you just want for your middle part, to look as flat as possible. I'M also going to take something that got to be spray and spray that all over the top of the hair, not too much, but just enough to make it have some shine. Lastly, i'm just going to correct my part in over bleach knots that i may have messed up on. So i'm taking a piece of hair from the back of my head and laying that down in the middle of my part, making sure that piece of hair is not too big. And i'm also using like this uh semi-permanent or like corrector spray that i got from my hair store and i'm just gon na spray it over that piece of hair when you pull it back, you'll see that the part will be like a perfect part. If it's done correctly, so definitely take your time while doing this. But yes, this is just like a quick little wig hack that i learned and that i like to use and it definitely helps correct any like mistakes on your parts or have to help you get that perfect part [ Applause ], and that is how you get A perfect part on a closure install, so that is everything for this video. If i missed out on anything or if you want to know more about anything in this video make sure to leave me a comment below also check out the hair from unites hair, because this hair was super silky and they got bone straight. I probably will reinstall it in diet jet black, so i can have that jet black middle part bust down, you already know, but yeah. Let me know in the comments what you guys want to see next for hairstyles or what type of videos you want to see. Next or just let me know if you found anything in this video helpful and i will see you all in the next video, i thank y'all so much for tuning in make sure to subscribe, hit that like button and turn on the bell notifications. So you are notified when i post my next video. I want you around bye,