Highlighted Straight Frontal Wig Install

This is the wig i'll, be installing i'll leave the link in the bio. I honestly forgot the name, but, as you can see, it's a regular brown highlight 28 inch. So, as you can see, i used the board cap method and i'm taking my bolt hole, glue and i'm going to basically just do three layers of this and then spread it evenly and then once it turns clear, that's when i put the wig on the hairline. Don'T change so once i get it on the hairline and i place it how i want. I basically take this hair type thing i use and put it on the lace and keep it on for a couple minutes. Just so i know, like you, know it's secure and dry and it's not gon na move. So after a couple minutes, i take the headside thing off and i cut the lace in three sections: there's no real purpose. I just do it because it's easy and i cut a big chunk of the lace off, but not too much, then i go back in with a razor and then i start to cut closer to the hairline key is to start off small, because if you cut Too much lace off, you can't get it back. So that's very you don't important. I want you, i don't you got some houses after cutting all the excess lace, i'm gon na go in with the lace glue spray, i'm not even sure what it's called but i'll leave it in the description. It'S the black ebbin spray - and i just put this all around just to make sure like everything, is glued down and then i'm gon na proceed to put the head thing on. Actually, i put my elastic band on after this again for a couple minutes, so it could dry hold. You can use a blow dryer to dry it faster, but this was one o'clock in the morning. I had nowhere to go so i wasn't in the rush. So i put the elastic band on for a couple minutes, while that is setting i'm going in and basically molding, the top of the wig like taking a hot comb and just making sure the wig is flat like flat. You do not want to be out here with a bumpy wig, so take that hot comb and make sure it's flat. I parted it make sure my part was right. I'M going to take the band off in a couple seconds. You'Re going to see me fix the part, but the product i used is the edge booster wax stick and that's basically going to help mold the top and make this flat as possible. Like i said before, this is me basically fixing the part without the elastic band. On just making sure you know no imperfections making sure it's straight yeah, all that good stuff. So this is the next morning when i decided to finish the install like i said i was doing this one o'clock in the morning. Basically, i'm taking this foam and just making sure like the hairline, isn't hard from the glue loosen it up and i basically just part a section of the hair and start plucking now. The key to plucking is, do not pluck in one spot, basically have to keep moving your hand periodically, but you do not want to plug in one spot or you just got to mess up the whole hairline. So what you want to do, move out the baby hairs that you're going to use and just go layer by layer pull some back each time and just keep plucking to the desired look. You got some houses so once you're finished plugging and you get that desired. Look, you want to start your baby hairs. I did one side off camera, but basically you're just gon na take the layer, you want use your razors to cut it down short and i use the wrapping foam and i swoop till i get the desired look. I want um uh now that all the hard work is done. It'S time to style the wig. I decided to just go ahead and straighten the wig. It'S already a straight haired wig. So i just went for the straight hair. Look, you know, i don't do straight. Hair a lot so this was not new but out of the norm for me, so i decided to go ahead and straighten it. These last few steps are optional, but this is what i do to get that you know flawless. Look i go back in with the wax stick on the hairline. Just to give it a nice, you know shine sleek. Look then i'm gon na go back in with the hot comb, make sure everything's flat, because i hate bumpy installs, like my wigs, have to be flat. So that's what i do, i'm going in with this spritz hold and i'm putting it on my baby hairs, because this will make it stay like. If you ever get your hair done from a stylist. You don't know how to like redo the baby hairs. They do get this braid because it would hold for like three four days, then i'm taking this hair oil. Basically just you know rub it in give my hair some shine, and that is the look guys. That'S literally the whole install the whole process, and that is the end of the video. Thank you guys so much for watching. Don'T forget to give this video a like comment and subscribe and i'll see you guys in my next video