How To Make I Tip Hair Extensions

Hey guys, it's Theresa today, I'm going to show you how to make I tip hair extensions. So the first thing that you're going to need is your hair. So I'm using the same hair that I did in my last hair video, then you're going to need some scissors so that you can cut the hair off the web and next you're going to need these little keratin beads, which I got off eBay. I will put the link in the description box below and they're just little bitty B, that you're going to put on your flat iron, which brings me to the next thing, your flat iron, that you need so you're going to need this to melt your beads, and I use these cruisers right here to place the beads on the flat iron, okay, so you're going to take your scissors and you're just going to cut some hair off the wet. You don't need that much, but you'll find out later that I used a little bit too much and then you're just going to gather it together and try to make it as even as you can at the top. But it's not really going to matter because you're going to cut it so see. I just only have a little bit of hair. Now I'm using my tweezers, like I said, and I'm just placing the little beads the keratin beads on the flat iron, and I saw this in a video that somebody used to be so. I decided to use two as well, but you really don't need to. You really only need one bead, so you just place the hair on the flat iron and just close it, and you can really actually just close it and pull the hair through which I found out later as well. After you get the glue on the hair, then you want to just take it and twist the top, and you want to make sure that it's round and slender so that it will fit through the bead later when you install it okay, so there's the first one That I've done so now. What we're going to do is we're going to take our scissors and cut the top off we're just going to make it nice and even at the top, and there you go, there is the completed first, I type hair extension. So now I'm just going to take some more hair that I cut off of my width and I'm just gon na gather it together again. Now I'm going to go ahead and get my beads on my flat iron. So with my tweezers again, I'm just gon na drop those beads on there, which still at this time, I didn't realize that I didn't need to be that I only needed one. So I'm still using the two I'm just gon na. Let those beads sit on that flat iron for a little bit just so that they can melt, and I saw on another video that you can just squeeze the flat iron a little bit just to make them melt faster if you're, in a rush. I'M going to take the hair and dip it in the glue a little bit flip it around, and then I'm going to close the flat iron and make sure that the glue gets distributed evenly throughout the top part of the hair. Then I'm going to take it and roll it to begin just to make sure that it's nice and round, and then I'm going to take my scissors and cut off the straight ends that are at the top there you go after. I got my two hair extensions done. I was like, let me make sure that these fit in the bead, because it looked a little thick. I took one of my beads out of my jar and the beads that I bought are the ones with the rubber on the inside, so you need to make sure that your hair extensions are thinner than normal. I would think so, as I was putting you, then I realized that my hair extensions were a little bit too thick, so I took my flat iron and just put it over the top again so that I could warm that glue up and just separated the hair Extension into two and you just need to just roll it up at the tip, like you already did before, taking my scissors, I'm just going to go ahead and cut off those straight end at the top. Now I have my two hair extensions. So that's a way that you can either add or remove hair. You just add the Flatiron or take the Flatiron to the top of the hair and just warm up that glue and you can either remove some hair or you can add some more hair and just warm it up and twist the top. As I was doing these, I decided that I was going to go downstairs and come up with a plan, so I had my Flatiron right there and my beads right there and then I had my hair and I would just place my beads on my Flatiron. Let it sit there and then take my hair and just push down on the flat iron as it was on the table, and I was able to go a lot more quickly with that method. Anyways. This is a hair prior to cutting all the tips off, and this is the hair after I cut all the ends off, so I did need to go back into some of these extensions with the flat iron so that I could remove some hair because I did Make some of them a little bit too thick, but this is how they came out and I will have another video on how to install them so stay tuned. Thank you so much for watching. I hope that you guys enjoyed my video and please subscribe, but today, I'm here to show you how I install my weed using the rubber band method. So I'm going to go along the left side of my head and I'm just going to rubber band braids and then attach more hair okay. So this is how it looks on both sides.