Nylon Head Wrap With Bow Tutorial. How To Make Hair Bows. Hair Bow Tutorial. Laco.

Hello, everyone welcome back to my channel today we're going to be making these super soft nylon head wraps with bows on and this fabric i got from aliexpress. I will pop a link in the description below it comes in many different colors, and it comes just in a long strip. You can buy them in one meter length. I actually bought three meters and it is like a tubular shape. Almost like the leg of tights or hoisery. It actually came in a bag. Just like this, and to be honest, it was super creased. I did actually run the iron over these, but you have to be very careful because being nylon, it will just burn very easily, so you have to have your iron on a very cool set and i've actually got a nylon setting on my iron. So that is what i used and i just laid the strip out and ran my iron over. It still a little bit creased, but that won't matter too much, because when the bows are popped on the head, the fabric is stretched out and it doesn't show any of the crinkles anyway. But these are super cute. These are one size fit all. As you can see, this is small enough to fit a newborn head and it stretches to fit up to an adult size head. These are fantastic for the spring summer months, because they're, nice and thin so they'll be nice and cool on the head, unlike if you say had like a bullet or liverpool fabric head wrap. That would probably make you a lot more sort of hot than this. Would this is a lovely cooling material? This is also the same material that makes the one size fits all nylon headbands. So if you've got any little bits left like, i could probably use this for a bow still. So it's not that small. If you've got like a little bit left, say sort of half this size and you think, oh, i can't do much with that. You want to cut it into about a four or five centimeter wide strip. So if i show you this unraveled, that is basically just a strip of around four centimeters and these are like a tubular shape and then you just wind it and pull it around your fingers and that will automatically sort of curl round like this has, and that Will make those little dainty or nylon headbands, so any leftover pieces you can use for them as well, so for these headbands one size fit all. You want to cut a strip at 30, centimeters, so 30 centimeters for the main part of the head wrap. Now i've got my board here, and each of these squares is a centimeter. This thick line here is the 30 centimeter mark and i'm going to be cutting it using my rotary cutter. I also got this from aliexpress. I will link this in the description below also, and you need a firm ruler. I'Ve got my metal one here and i'm going to line that up against the 30 centimeter line, making sure my fabric is in line with the end as well, and then i'm just going to cut that off at 30 centimeters now. That is the easiest way. I find to cut it is using a rotary cutter. If not, you can use scissors just measure with your tape, measure or ruler and just cut it with scissors, so that is for the main head, wrap part of the bow. Next, you want to take a needle threaded with some double strength thread and just pop a knot in the end, and then you want to fold your 30 centimeter piece of fabric in half and you're, going to sew a pinch as you would a ribbon bow across These ends these raw ends to join it up, so i'm going to go in through the first corner and then just continue all the way across around half a centimeter from the very end. I don't want to go too close to the end, so i want to make sure i catch all four layers of this fabric and then, when you get to the end, just pull that tight, keeping that pinched in place and then i'm just going to go through That end and then through that loop a couple of times before i pull it tight and that will form a knot to hold that all in place like that and then i'm just going to trim off the excess thread trim that little tail end down as well. There'S no need to turn this inside out so that this piece is on the inside, because we won't see that when we've done the finished head wrap so just pull that tight, and that is the main part of the head wrap done for now. Next, take in your fabric, again, this is for the bow, and this time we are going to cut 25 centimeters, so 25 centimeters for the bow. So again, that is a another dark line on my ball, to make it easier. So i'm going to line my ruler up with the 25 centimeter line on my board, making sure, as in line at the start end as well, then i'm just going to cut that fabric off. So we've got a piece at 25, centimeters and 25. Centimeters makes a 10 centimeter bow on the head wrap, so i made this one exactly the same as what i'm now showing you again we're going to fold it in half and we're going to stitch this end exactly the same as we did the head wrap part. So taking the needle and thread again, i'm just going to pop another knot in the end and then i'm going to sew these raw edges together and then the same again. Pull it really tight. Keeping that pinch in place go through the end and before you pull it completely tight, go through that loop, a couple of times to form a knot and trim off the excess thread. Again, you don't have to turn this inside out. You can keep it as it is open it out and lay it flat. So you've got now your two pieces, the 30 centimeter piece, which makes the head wrap and the 25 centimeter piece to make the bow taking the piece for the bow we're going to slide. It inside the wrap and we're going to line both of the joints up, so it's crossed over like this and then you're going to bring both of these ends up. So we've got both of the ends of the bow piece and we're going to tie it. So just cross it over bring this piece over and under and start to pull that tight. I'M just going to lay this out, so i can see the top of my head wrap and then we're just going to keep fiddling with this bow to shape it up. So i'm going to pull the loops that way and the other side pull the loops across sideways, pull the head wrap down, and i'm just going to keep doing this until i'm happy with how the bow looks and how it's sitting. So i'm just going to twist the sides down, so i've got this nice little twist in the middle like that, keep pulling it so it's nice and tight as well. At the same time, see there i've just pulled out the seam part, so i'm just going to pull this side of the head wrap. So it goes back in under my bow and then after a little bit of fiddling and pulling and tugging you've got your finished head, wrap with bow with that nice little twisted center as well. So there's the pink one and then we've got a nice bright white. One i've got this black one here and i also did this car key color. I hope you enjoyed this tutorial today. If you did, please hit the like button, don't forget to subscribe to my channel and also press the bell button to turn on notifications and then you'll always be up to date. Thank you for watching everyone. Bye, bye,