Diy Women Occasion Hat Designed With Crinoline | Hat Making Tutorial

Hello, beautiful people - you welcome back to my channel if it's your first time, hello and welcome back so today. I am here to share my knowledge with you again. I found this out. I just came across this beautiful queen in hearts on pinterest, and i just feel i should try it out. I did i documented the whole procedure and i'm here to share my knowledge with you. Please do not forget to hit the subscribe button if you're here to join us here, please hit the like button and share with others. So let's get started okay, so this is what i'm going to be using for my base. It'S actually blocked with paper mat, and i use this wooden um objective scene to make this shape. Okay, so i have all the materials. Like my hot wire, i have my my bare strip needle and thread in place of the joint thread. I may actually be using fishing line while working this fishing line is about 0.25 mm. I also have about 0.30 mm. You could use any of this. I have uhu glue. I have green lining. The crayon is about 6.5 inches wheat and the total length i have is about 10 yards or 10 meters. 6.5 inches. Is the width of this mine really neat? I have a pair of scissors glue, gun and the glue stick. I also have my elastic band. You could use the plastic headband in place of this. Like i said earlier, i've blocked my beads and this is it it's dry and the next thing is for us to wire it. So i have my art wire and what i i did was to measure the mode or the art block. This is that a block i used in blocking it? I just measured it, and then i got my artwire okay, so i'm trimming off the excesses. I already did that i'm just trying to smoothen it up and do it perfectly before i proceed to the next step, so i have my out wire, so i just measured the most. Can you see, i just measured it around to get the exact length of hot wire i'll be needing, so i have about 20.5 inches and i added extra three inches about two point. Five to three inches is fine for also overlapped the wire okay. So that's the measurement i use in cutting out my wire, so i'm going to place the two ends of the wires together. My paper tape, which i'm going to be using to join the two ends of my wire. So i have the two ends of the wire brought together and i'll, be using my paper tape to secure them. Remember that i had three entries extra while i was cutting my wire okay, so that three inches asked to go. Why you overlap? I mean you overlap by 1.5 inches on one side and 1.5 inches the other side making into three inches so that at the end of the day, it's going to fit into the base properly. If not, it may become bigger or maybe come too small. If you don't do the measurements accurately? Okay, if you don't overlap by the extra inches we added earlier, it will actually show so i'm using my paper tip now to wrap over to secure the ends of the wire together. Foreign is when you're wrapping your the two ends of your wire together. Make sure that you don't have it too swollen or else it will show it to actually be visible on your first needle you're at so i'm just going to be inserting the wire into the base. As you can see now, i went ahead to use my alt glue to seal the wire to the ends of the base. As you can see, okay at this point, you need to be very careful, you're applying little glue, and you just apply pressure just cover up like that and apply pressure so i'll be doing that round and once that is done, the next step is for us to Start designing our base. Okay, so i have my needle and fishing line. Yes, i've traded, my needle with fishing line and i'm going to start using my crayon need to design this base. At this point, i would like you to please watch the whole process. I may not be able to explain like that till the end, but i would like it to just watch so you can see all i was doing: okay just to design this okay. So i'm just starting by folding my cloning into two. This way, and i bring the ends together, bring the ends together like this and i'm going to tie okay. So i'm using my thread to tie one end of the cranny and to seal the ends of the fraying edge of the crinoline properly. I applied my glue and then just a light dry little then i just press it down, so you can see so that will seal the edge off the cranium. Now i'm just going to go ahead and then start tacking, my crinoline to my base. Okay, so please watch what i'm doing, i'm using my needle and fishing line for this. The point i just marked is just going to be the back of the art, so that will give me a guideline. Oh just that would give me a guide on how to go about designing the base. So i'm just starting from where i have my left thumb, okay i'll, be using my needle and try to do the tucking and i'll just tuck the cradle in like that around the base after the criminally down. And that's my starting point like i said earlier. So i'm just wrapping the cleaning around the base. Remember i folded the cranial net into two, so i picked the two hedge all the two. Yes, the two edges like that, while i wrap around okay, so i'm going to be doing some tuckings like that. While i take the cranial new round i'll be lining the inner parts of my base, so whatever attacking i do that may look. Rough inside will definitely be covered. Okay, so you can see me using my needle and fishing light to tap and you do i mean tuck the wheel into it and the way i'm talking on the outer part of the fascinator or art you'll notice that the thread does not really show invisible attacking. I can actually tack anyhow from inside, but from outside, make sure that the tarkins are not that visible, hey i've gotten to this point where i'll be making a row, so i just measured what i will need. What will be enough for me to make my rows? Okay, i have about 12 inches from that point and i trim off the excess quinoa and i tied the end like i did the other time. Then i finished up by making a rose piece watch just watch what i'm doing - oh foreign, so wow my now foreign. So i'm done attaching the three layers of crinoline to my base, and this is what i have left from the 10 years. I started with from the tire that is left. I actually took off about 30 inches. Yes, i kept that, as i actually used that later in the video. So this is what i have left right now, after cutting out the 30 inches, and i just folded the crayon in i put it into two. I tied the end and i'm sewing the stitches from one edge to the other end. At this point, while sewing my loose stitches all the way down, i discovered that my trend became short, so i had to just pull the thread. I just put the thread together. It at this point so that i can have enough thread to continue sewing those stitches. I just went ahead to sew the stitches like that i'll. Do it down i've sewn my loose stitches out to the other end, and i just pulled like that together a top and i went ahead to arrange it properly, wow hey, so our design is um done, and i just place it like that on this part of The first needle out - and i tucked it down now - the krylon i have left now is what i cut out earlier that i kept aside earlier, so i'm just using that to still design this uh beautiful heart. Please watch this part as you can see. I folded, including into two and i've tied one end i'll, just use it to this round. You can see the way i'm just trying to wrap the crinoline from the thunder part of from that part of the fascinator base. You know it all depends on creativity. You can always form something different from this. Okay once you understand the technique, so i just place my queen in like that. I'M going to tuck it like that round. It'S i've taken the crinoline around the base. To the point i want it to be, so i just measured about 16 inches, i just measured about 16 inches and i cut off the excess. So i'm just going to tie that in and i'm going to use it to design that part of the fascinator. So at this point this is what i have and i'll just go ahead and attach the elastic i'll just use my needle and thread to tuck it to the point i want it to be. The elastic is about 13 inches about okay about 15 inches. It depends on how stretchy the elastic is. Okay, it could be 13, it could be four thin and i just tied each of the end and i'm going to tuck it down to my first little bees. As you can see, the elastic is fixed to the first nature and it's as firm as much as possible. Then i just went ahead to line the inside to cover all our tokens and all that covered this part with my bias strip, as we normally do. I also covered every rough edge with accessories or embellishments okay, and so we have come to the end of the tutorial. I hope you have learned one or two things. I hope you enjoyed this video. Please hit me like share and subscribe if you're here too. Thank you so much for watching this video. I will see you all in our next tutorial. You