Bat Hair Bow! How To Make Hair Bows. Diy Hair Bows Laços De Fita:

Hello, I'm gon na show you how I made the template for these little back pinch bows and also how to make the finished bow. So these two, the first two sides as I tried out these little mini ones, which measure just two inches across I'm thought: they're ideal for wearing in pairs. And then I want it to make one bigger and this one measures around two and a half inches across. But I actually want it a little bit bigger, so I'm going to make this next one even bigger than these. To make these, I started off with a rectangle two and a half inches across by two inches down and this one I made my rectangle three and a half inches across by two and a half inches down. So this one I'm now gon na make with you guys, I'm gon na try out a four and a half inch wide instead of three and a half inch and I'm gon na go for, I think three three and a half inches down so we'll go for Three and a half inches down by four and a half inches across I'm just going to join these up together. So you have your rectangle brought out. I'M going to cut this out just doing it roughly! So don't matter too much! I just want to quickly show you how I make there is now using your wider width across, which is the four and a half inch across you want to fold that in half and then using a pen from this outer flap, the open flap draw a line Going from the middle diagonally to this outer corner like so, and then from this outer corner to the bottom, diagonally again that don't have to be too neat and then cut then tips off. So you should now have a shape. Looking like this, so next keeping that folded on this open edge, you want to draw your little spikes. So I'm going to roughly mark two dots around the third of the way, so that you can then make your three little semicircle. Should I say, and that will make your little spikes on the edge of the bats wings again, you don't have to be too neat and then cut those little arches out. So you should now have your actual template shape made, but obviously papers not any good. So I'm going to take a piece of card v, 350 GSM card and I'm going to transfer this template onto card. So well, then, got a template that I can use again and again so holding that down firmly I'm going to start drawing around my piece of paper template it's quite difficult, so obviously, with it being paper, that's quite thin! If you go round it very gently, you can just feel the edge of the paper with that pin and then you can just glide along the edge. So once you've got your template all cut out, you think back to keep and use again and again, and now I'm gon na show you how to make the actual bow using your new template. So, to make my little back Clips, I've been using this fine black glitter. So on the backside of your chosen fabric, you want to draw around your back template. So there you have your outline drawn and then take your pair of scissors. You can then cut that fabric out, so once you've got your template cut out. You can then make your pinch down the center. To make my pinch, I'm going to use a piece of black thread: cotton. 3. So you want to go down roughly along the middle, to push your thumb in and bring that by the side and then bring the outside one down and then another up and down at the bottom as well. So you've got one two three four little pinch place on that thread, underneath your thumb, leaving a tail to tie making sure that central wrap that thread around the center a few times, I'm not going to pull it too tightly. So I don't want to tie it pinch just to hold that in place and then tie that off like so and there you have your little pinch back bow shape, so I'm gon na be using double pronged clip today, which I've already lined. You could attach this to a headband, Dallas band and elastic, but today I'm using a clip so take your clip or whatever your loop using and place a little bit of glue just on there and then pop that in the center of the back. Your bow and once you're happy that that's stuck on there nice and securely take another piece of black glitter, I'm just using this scrap of cut piece and I'm going to cut along the longest bit. I'M gon na cut a strip just to go down the center. I prefer to use scrap pieces for my center Center strips so that piece was perfect just to cut a little bit out and that's a cut off the main body of fabric place a little bead of glue along the end of that center strip, open up the Clip and line that up with the center of your pinch and then bring that around the middle of the bat not pulling it too tight. So I like to leave a little bit if you pull it too, tight that'll make that really small in the middle. I like to leave a little a little bit loose along that little bit if that makes sense and then finish off with glue in the other end, underneath the clip there, you have your finished at bow hair clip. So this one we just made was the four and a half inch rectangle by three and a half inch down. Wasn'T it yeah this one was three and a half inch across by two and a half inch down which makes that slightly smaller and these little itty bitty ones worth two and a half inch acrost yeah and two inch down so there's three different sizes there. I hope you enjoyed this tutorial today and have fun making your little bat bows any questions pop them in the comments and I'll do my best to get back to you. Thank you for watching bye, bye,