How To Make A Ponytail Beanie

Start a regular domestic sewing machine and we're using a singer' heavy-duty your fabric and we're gon na be using a rivet next you're gon na need your pattern, and this pattern is available at profit for clothing comm. It is super easy to use. All you do is download it print it off and you're ready to go once you have your pattern, go ahead and cut it out on the outside of the black line and then tape it together. The first step is taking your pattern, placing it on the fold and the fabric tracing around it and then cutting it out and make sure when you're working on the folded edge. You'Re only cutting to the point that is indicated on the pattern and when you have unfolded it should look identical on both top and bottom. Then go ahead and fold it in half with right sides together, because you're gon na be sewing off the edge on the opposite side of the fold and you're. Only gon na want to sew the two peaks, not the middle, so with right sides together, go ahead and sew those two peaks in center using stretchy fabric, go ahead and use a zig zag stitch next word in making the ribbing for the ponytail hole and we're Just gon na straighten it out a little bit to see what the measurement is. We'Re gon na want this to be smaller than the actual hole, because with ribbing you want to cinch together. So it's about seven inches across. I recommend going to about four inches. Keep in mind, you're gon na be rolling this over, so you're gon na want to double the width. We did our width about two inches. So when it's folded, it'll come out to about an inch and the wider, you go. The less noticeable that hole will be so we're gon na go about 1 inches and see how it looks. But I don't recommend going any longer, because a pride is bunch up and be more noticeable. So now that we have that little cuff cut go ahead and sew that middle edge and then once you have that side sewn together, go ahead and pull the right side out and then you're gon na push half of that right side back in over itself. It'S kind of similar to doing a coffee just trying to fold it back in over itself, so that the tops line up so go ahead. Work with it play with the fabric a little bit make sure it's nice and flat and halfway folded in that all the peaks line up at the top so grab the little coffee, maid place right sides together and sew the edge and you're gon na want to Roll the wrong sides together so that way it's right on both sides. Next we're ready sewing this into the ponytail hole, but, depending on how wide you made this cuff, you might want to just go ahead and sew all the way around the edge. So that way, it's easier to sew all these pieces together, and that is what we're gon na do really quick we're just gon na sew that cuff and make sure it's all one piece, and once you have the edge of that cuff zone, go ahead and place The right side of the cuff to the right side of the beanie and you're gon na want to sew all the way around that circle kind of like putting a cuff on a hoodie and don't worry. If it sticks out a little bit, you can either adjust the width or we're gon na. Show you how to top stitch to make it look more flush. Will you have the inside out go ahead and take the two peaks at our opposite side of the side? You sewn together place right sides together and sew that edge stretch it out line up the two middle seams and sew all the way across that top then go ahead, pull the right set out and adjust the bottom fold to where you want it, and then the Last step is doing a top stitch all the way around the outside, or if you don't want to you, can totally just leave it, but the top stitch is going to flatten out just a little bit and make it more flush. So just sew right along that edge. All the way around the ring and again playing with the width of that cuff, can really change the look in the beanie. I also think we could have went a little bit shorter about three inches and it would really cinch that together and make it unnoticeable, but yeah definitely play around with it and see what works best for you. Thank you. So much for watching be sure to LIKE subscribe comment. Let us know your thinking. If you have any ideas for videos, send them our way, we'll try to make it happen for you until then we're gon na keep videos coming at you. So we'll see you next time,