Detailed Half Up Half Down Flip Over Method 3 In 1 Wig Texture | 90'S Style/Look

Foreign I'll be installing a wig from Eon, hair inside the package. I received the wig and a wig cap for the bowl Cap. This is what the wig looks like straight out the package. This is supposed to be a three in one wig, meaning that it can be kinky straight straight and deep wave once it's wet foreign, as you guys can see from the thumbnail. The style that we'll be doing is kind of a half-up half down with two strands of hair left out and I'll be styling it with no baby hairs. This is what the wig looks like on my client's head. As you guys can see, I already pre-mapped out everything how I want it to be so I'll, be showing you guys how I install it and mold it into place foreign applying your layers of glue. You want to make sure that you clean the area that you will be applying the glue to so that it can stick properly the glue that I'm using is Erica J's homemade down adhesive. I use three thin layers of this for each install foreign foreign layers have dried. You can then proceed with placing the lace into the glue. You can line the lace up with a dotted line that you made before placing the glue on foreign. Once you finish, placing the lace into the glue you can have, your client hold both sides to make sure that the wig is secured and it stays down foreign. You want to make sure that you cut it in a zigzag motion so that when it's off it doesn't look as visible for this install, it won't be styled with any baby hair. So you want to make sure that you cut in a zigzag motion throughout the entire hairline foreign, as you guys can see. The stranded hair that I had down to be by my client Sideburn is a little bit too up and it doesn't match up with her hairline, so I will be pushing it back and pulling some hair down continue watching to see how I fix this. I first start by cutting off all the lace that needs to be cut off now, I'm just replacing where I want the strands of hair to lay since the hairs that I'm pulling up and down were originally there. It wasn't plucked before so now, I'm just plucking. It to match my client's hairline foreign, please foreign. I repeated the same step on the other side. Now, I'm just applying makeup to the areas of the lace that need some blending to match my client's skin tone foreign, since there will be no baby hairs done for this insole. I use my Bed Head holding spray and left the band tied down with it. Until I was finished, flattening the wig, this is what the wig looks like in its natural state. I would consider that kinky straight and then the roots of the wig kind of look like a deep wave, but my client wanted it straightened, so we'll be straightening. The entire wig for this install, thank you, foreign. This is what the wig looks like after I straightened it. I try to straighten it as straight as possible, so this is the outcome foreign I placed a little bit of Biosilk in my hand and I'm just rubbing it across the front of the wig. Before I start to hot comb, this wasn't a full frontal wig, meaning that the parts that I'm about to how come there are tracks behind the hairline. So I had to try to get it as straight as possible so that when I place it into a ponytail with the got to be sprayed, it looks super flat. Foreign foreign, foreign. The first part of the wig that I slicked back was the middle section, because this part will be slicked all the way down, and the two sides will be the ones that will be in the ponytail. Once you slip back the middle you're, going to move on to one of the sides of your choice, once you've sprayed the freeze spray on the hair you're going to comb all the product throughout the hair and then blow dry it into the direction that you want. The ponytail to go once you've gotten it flat and molded the way you want it. You'Re gon na use a clip and pin it down until you've done the same thing to the other side, foreign foreign. Now that both sides are molded into place. I use two small rubber bands and placed it into a ponytail together once I secure the ponytail, I then used another set of rubber bands and flipped the ponytail over, so that it can be visible in the front for the ponytail that I made. I didn't put enough hair in the ponytail, so now I'm going to try to use a comb and tease the hair so that the ponytail part can look bigger and more visible when my client is facing forward. So I use the got to be glue, free spray blow dried it a little bit so that it can be somewhat stiff, and then I just use the comb and tease the hair. Thank you. Now I'm using my Ruby, kiss cream foundation, I believe it's number 10 or 11 and I'm using my angled brush to outline the parts, so they can be more visible after I'm finished outlining all the part. I then use the same makeup and placed it on the hairline of the lace and rubbed it in, so that the lace won't be as visible foreign to complete the hairstyle. We decided to trim the two Sideburn hairs that were out and we gave the wig a blunt cut foreign. This is the finished look. I hope you guys enjoyed watching and let me know what you guys think in the comments foreign