Watch Me: Color & Install A T-Part Wig W/O Bleaching The Knots(Beginner Friendly) ☻

Hey guys welcome to my first youtube channel and as y'all can see by the title: um i'm gon na be installing a tea party wig and if you're interested make sure you like comment and subscribe and keep on watching. So you want to take your 613 here and you just got to be glue and spray. The knots here, i'm just wetting the hair so that the color could coat the hair evenly. So you want to use any container that you don't use and fill it up with hot water. Moving on to the coloring method, i first used the color cajun spice, so here i'm just putting water in the bottle and shaking it up and taking all of the color out of the bottle. You want to mix it then i'm gon na use the color slimming. Second and repeat the same steps so for the last color, which is french cognac, we're going to use only half of the bottle, as you can see, i'm combing the hair to ensure that every strand has the color. What i like to do is use the left over water and pour it onto the hair. So when you're done braiding your hair, you want to do the cap method, but before i do that, i'm going to put edge control to um smooth back my fridges. Don'T grease my mix because i guys don't know how to braid on myself, i know how to braid on other people but myself to prepare myself with the ball cap method. I'M going to be using alcohol around the perimeters of my hair. Now i'm just cutting out holes from my ears. You want to spray, got to be free spray. On the perimeters of your hair, i went ahead and did two coats of the got to be free spray and off camera. I applied makeup on my wig cap and on the insides of my wig. So now you want to add alcohol to clean up excess makeup for easier application. You want to cut your lace into three parts. I applied ghost bomb glue to the first section, which is the middle section. So now, what i'm doing here is spreading the glue down to my skin, make sure it's half inch on the cap and half inch on your skin. We'Re gon na do two layers of that and each make sure each layer is clear when the glue finally becomes clear, you're ready to lay the lace down, and here i'm just using a comb so that the lace could stick to the glue better. Because this is a 13 by one t, part wig, meaning that it's only parted in the middle and it reaches from ear to ear and only one inch spacing in the front. So it's hard to create a natural look, as you guys can see. As the video goes on, i'm gon na make it into a 4x4 wig. I went ahead and repeated the same process to the two last sections. I'M just cutting the lace around my ears for comfort to make sure that the lace is glued down. You want to go ahead and use an elastic band to make your wigs look flat. You want to use a wax stick here, i'm just showing you what kind of wax stick i'm using, but you could use any of your choice and then, after that, i'm going to use a hot comb and you'll see the magic. Now i know y'all see a difference. You see how flat my hair is now versus how it was before. So you better invest in that wax sticking hot comb girl. So i'm going ahead and flat iron one side, i'm gon na do the other side and come back both. Let'S try to take this off. What i'm going to do with this part when cutting the lace, you want to use a razor or a scissor using the zigzag motion. They sent me a small wig, so i had to leave some lace on the hairline. Now, i'm just going over the lace with some makeup. If your lace is lifting up like mine, you want to go to that section and apply glue on it. So now i'm just taking out hair to create baby hairs and then i'm going to go ahead with the tweezer to thin out the hair that i just pulled out. So now i'm just cutting out some baby hairs and then i'm gon na use any type of mousse to lay my baby hairs off camera and come back when you're done creating your baby hairs. You want to use a scarf and tie it down for 10 minutes when putting makeup on your part. I want to share a tip which is using a q-tip and putting makeup on it or using the back of a rat tail comb and putting makeup on it and then apply it to the part and voila. I did the q-tip method two times a few moments later, thanks for watching. I hope you enjoyed this video and the final look make sure you like comment and subscribe. Peace