D.I.Y How To: U- Part Wig Side Part (Pt 1-Hot Glue Gun Method )

Okay, so today I'm starting off with my Malaysian seven piece pack of hair: it's called the shake and go by cube and it was really inexpensive about twenty three dollars and I'm using a dome cap, a hot glue, gun hot glue, stick scissors and the only other Thing that I did not mention was like a white pencil or something to make your part wait. So you know where to cut it. So with the wig cap, I put it on the mannequin and then I take the white pencil and then I draw out where I want my part to be for when I'm done just so. I know where to stop the track set with the hot glue gun method. It'S really really easy. You basically just measure the well as you can see, and then I will place the hot glue gun on the wet and then I will place it on the mannequin. So you measure it you're gon na cut it put that glue gun on it. What put the hot glue on it and then you're going to place it on the mannequin now the good thing about the hot glue is that it does not stick to the hair. So you can pull it off very easily off the air and it does have a good hold on the dome cap. So again here I I'll find a good. You don't have to put the hot glue. You don't have to put it all. You know on the whole width: it's too long, cuz the high glue does dry fairly quickly, so you can do like half and then do the other half which you will see here. Well, I just did some and then I did the rest. So this is a very simple wig making process, especially for beginners, if you're not that experienced with leeks. I always tell people: do not go out and buy the most expensive hair that you can find if you never made a wig so and if you do get the expensive hair, I do recommend doing the photo of a method and also sewing it on the dome Cap, which I will do another video for that, so you do want to see that video. You can't thumbs up this video and I will definitely get that video done for you guys the photo of a method but the hot glue gun and also sewing in the hand. But, as you can see, it's it's fairly simple. You just measuring cutting applying the hot glue, pressing firmly on it on the dome cap, and then you know: that's it. Dean wants in the next part, so I'm gon na. Let you guys just finished watching me: do this cuz it's self-explanatory now, once you get closer towards the top of the hair and to your part, then you can start making smaller pieces of width and just laying it you know across like horizontally. So you get to the part, so you know, as he get all the way up to the part, and you kind of just do it by your judgement in regards to the top of the hair. As long as you get to the part - and it looks seamlessly like it lets go, he says then you'll be fine to where, when you cut it out, it doesn't look all jagged and things like that, so I'm just gon na do that for the top of The hair just kind of make smaller width or either. If I feel I can bring it all the way around, I will I'm just. You definitely do not want to go past the white line like over, because that's where your leave out is going to be. You don't want to be too narrow, because then it will look pretty weird. I mean you're a veneer, but you got ta be like a hump or something right there. So you don't want to do that and, as you can see, I just lid, I think the closest I get is actually laying it on the white line. But I don't go over the white line, so there you guys have it. It was super easy like to make this wig and then what you're gon na do is go ahead and cut out the part you're. You part you could just try to trim as close as you can just to get rid of any white, but you can take a damp towel. If you use like a white pencil, you can just wipe it off and there you go see open. U part wig and then, if you guys want to see how I apply, it definitely comes up this video to see how I apply it and do my hair under the wig or I leave a comment below, but do not forget to subscribe and to share this Video, let's give this a try, definitely comment below and let me know