Tutorial - Make A Large Tulle Hair Bow - Diy Make Your Own Bows

Hello and welcome to enchanted Sparkle crafts. Today, I'm going to show you how I make these tool helpers so to make this we need some jewel. We need to cut this to 4 meters in length and we just keep the width, as is I'll, put a link in the comments of where you can get really good chill from what I've always used. So pre clip this to 4 meters long. We also need some card. I'Ve cut this to 25 centimeters, the grafts any height doesn't matter as long as it is sort of taller than the actual chill. So we also need glue and a strip of glitter for you Center a clip and something to line it with now. I only have 45 millimeter Clips left at the moment in my own personal stash, but I would probably prefer to use 55 millimeters or bigger for this just so that the hole better in hair so finally ends of much I've cut there. It is so we just go to carefully wrap this around here, making sure it meets up either side and pull this arrived just enough out of that they always closes. You can see those tangled just make sure it keeps going flat Anderson sort of get banty all over each Keitha, so she can see keeps trying to pop off that nearly to the end, we need to do now. Alright. So now we've taken our chill off the cards. I don't need to do is try and find Santa when she's around there and fold it down in the center another side just going to pinch up and down all like concertina. I think that's what you call it just pinch in and again the same with this other side, it's not training police, but it will just snatch up in this. She just keep folding up and down, and up and down I was trying it is so that you lost falls face in dunks. I just think it looks neater when it's done so it's just like this and while you've still got it held, get your needle and thread through it. I'M just going to wrap it around the middle of few times play tight. It'S a few stitches in to secure it and snip that off. This is what I've got so far. I use quite a chunky bit of the glitter one and a half cents me meter width stripped for this, because I think it's nice, for it sure so I'm gon na gleesh do it lay that strip on a little of course, I'm gon na glue it to The side Matt so now that song I'm going to quickly line quit, although typically I haven't brought my lighter with Mesa, I got a heat seal. Your ribbon on this clip, as I say, you'd, be much better off having a bigger clip than what I have here. This is just the early Diddy 155-millimeter, but fifty five definitely would be dying. It'S now gon na glue this down the back. As you can see, this is way too small. For this you really do need a bigger clip, so 55 millimeters. I keep repeating it. You remember see this is a lot more fiddly than your normal things, because this is really Wiggly even after you've glued it's not like that stiff sort of hard backgrounds put it onto you know until we call quite a lot with it, so push that in there The trim this down taste is quite nice and tight. There we go. I do really like the easies they're, quite full, on buzz a very noticeable and very pretty so yeah there we go. That'S how I met one of these. My next tutorial is probably gon na. Be for one of these, it's a ribbon, rosette I'll, do it in a smaller ribbon for the tutorial. This is one that I've done for my dogs and I've done it huge for us. It'S it's absolutely massive, as you can see, cm size. Is that massive, but yeah they still give my next tutorial, while I'm here, I'm gon na show you the weirdest thing off meds there. I think it's weird anywhere made this bar holder with the dinosaur on the top that says bones yeah, that's my random! Make of the day so yeah. Thank you for watching this video on how to make a cool hair bow. I hope you find it useful and I will put the link of where I think it's really good - to buy tool from below. So thank you for watching.