How To Make A Tulle Hair Bow - Theribbonretreat.Com

Our first step is to cut our tool, and here at the rumor tree calm, we carry these spools of tool and we carry a huge selection of colors and also glimmer tool, and so the roles of tool are really really awesome for any kind of project. So you're not having to cut out huge sheets of tool and so you're going to roll out your tool and then cut four pieces out, one at ten inches: nine and a half inches nine inches and eight and a half inches. Now before we make our bow. Make sure that you have a needle and thread ready. I'Ve doubled mine and put a knot in the end, and we do have a tutorial for that. If you're not sure how to do that now get your piece of tool. This one is 10 inches long, and these spools a tool are about five and a half inches wide. So we're just going to take the tool and then fold it in half okay, so once you have it doubled and even on the side, we're going to bring bottom up or basically making a bow tie, bow town. We want that to be to be even so be centered where the words overlapping in the center then take your needle and your thread, bring it under the bottom and then under again and then out again under again and then just pinch right there and bring it Through and don't pug tug really hard, or else the knot will come through now bring it around back we're just going to tighten it a little bit. I just stick it through a couple times and then we're done we'll just cut it off with your scissors and that completes our first bow and then go ahead and do this technique with the other three pieces of tulle that you've cut out once you've finished. Your four bowls, we're going to put them together so take the largest bow and take your needle and thread and make sure that you have a knot in the end and then we're going to turn the boat to the back and stick the needle through and make Sure you stick it through the center. Sometimes the center is a little bit, but a little bit off from where the bow is made and then take your next biggest one and do the same thing. Okay and then just make sure that they're all stacked right. On top of each other and make sure that the the ends are even and then you can squeeze them together and then wrap the thread around and then when it's tight go ahead and take a couple stitches in the back. Just like we did with the little rose thread, and that finishes our bow, and now we just need to add the center. Now we're going to add a clip, and you can also add a headband to this bow, I'm doing a French barrette clip. So I'm going to take the spring out now, I'm going to turn my bow to the over to the back, it's hot glue on my French barrette and place it on the back of the bow okay, and now we're going to wrap more tool around the bow. So cut a four inch piece of tool from your ribbon, your tool, spool and then fold this piece a bunch of times. Now we're going to put a little bit more hot glue just in the center and we're going to add this tool right here and then just be a little bit careful because the the hot glue will comes through the tool and get your fingers. So what sets cool down now we're going to wrap this tool around our bow, and I just like to wrap it around until I get to where I can't wrap it anymore. So I'm going to stop. There add a little bit more hot glue and then place it there, okay and then just cut off the excess and now we're going to add a gem or some other type of embellishment for the center or you can just leave it like this. This is super cute too now we're going to add some embellishment to our bow and I'm showing you this cute gem right here. We sell these at the ribbon retreat calm, and this would look awesome on this phone. You would just put it right in the center and that would just totally give it a little bit of bling and then I wanted to show you. We have these gem sheets and these are super cool for this project. So it's a big sheet of gems and I'll show you what that looks like going these huge sheets and so I've cut off a row of three across and then I'm going to add it to mine before I do that, though, and when you cut them, you Can see a little bit of the edges right here and so to make those fold down? You can just take your your lighter and then shrink them down. Just like you would with ribbon it'll go away completely, but it does help the look a little bit. Okay, so now take your bow place, a little bit of hot glue on the back place, one end of the gems on we'll wrap it around and see where it ends. I'M just gon na add a little bit more hot glue right next to where we started right, so we're almost done now. We just need to add back our spring for the French barrette close it up, and here we have our finished beau bling and all. Thank you so much for watching and I hope you've enjoyed this tutorial on the tool. Hair bow please subscribe to our YouTube channel for more tutorials each week, and is it the reverse recom to get all of your supplies. Thank you.